This year Shini Group applied for two booths which separately located in E2P61 and W4J41 and with a gross area of 237 square meters. E2P61 booth mainly display automation robot series, hot runner series and Shni-Syncro Extrusion series of products, and W4J41 booth mainly introduce Shini’s new technology, new design and energy-saving series of products.
This time Shini exhibit its new development of HDD-U Heatless Dehumidifying Dryer. Drying plastics via compressed air and heatless dehumidify regeneration, being immune to ambient temperature and humidity, HDD-U can continuously provide low dew-point drying air to ensure stable and favorable drying. It is applicable for small batch drying of commonly-used engineering plastics such as ABS and PS, also suitable for pre-heating before plastics molding. Adopted PLC and P.I.D. control which can provide an accuracy of ±0.1 ℃. Equipped with air pressure monitor, overheat protection, warning system and automatic control of electricity consumption.
SCD-ES “All-in-One” Compact dryers combine the function of dehumidifying, drying and two-stage conveying into one single unit, specified for the production of engineering plastics material such as PA、PC、PBT、PET. Of them Optics SCD-OP type device is suitable for processing application of lenses, LCD backlight panel, compact discs, etc. Under right setup, it can provide lower than -40℃ dew-point dehumidified air. According to the influences regenerative temperature had on dew point, HDD-U set the dew point temperature range as +10℃~-40℃ to realize energy-saving. Set material volume each hour for 40% ~ 100% of the drying capacity and control the dry air volume by the frequency converter, so as to achieve the purpose of saving energy.
SGD Gravimetric Dosers are new products of dosing and mixing series which have masterbatch measurement and weigh rolled into one. They are applicable for auto-proportional mixing of masterbatch and additives. SGD is able to automatically monitor the addition of masterbatch and additives. Also it can fulfill automatic calibration when bulk density of material varies. With an accuracy of ±0.1~0.3%, SGD series dosers are suitable for auto-proportional mixing of virgin material, regrinds, masterbatch or additives.
STM-F series oil heaters adopt large-flow pumps with high stability, which is not only suitable for heating up Moulds and maintaining temperature, but for extrusion molding and applications alike. SIIC-A-R2 CFC-free Refrigerant Inverter Air-cooled Water Chillers adopt environmental and energy-saving water control system, as well as Danfoss frequency converter and compressor which are able to reach the accuracy of water temperature control of ±0.1℃ with control ranging from 7 to 25℃. It can also automatically collocate with the load from 11 to 36kW.
This exhibition, Shini will introduce its granulating and recycling system for large size of broken piece. SGS-80120150S Single-shaft Shredders will be showed with a PNL-MS-L4500 belt conveyor with metal detector, a SG-3675 sound-proof central granulator and a CB-36 up-feed belt conveyor as one unit, which is used to shred extra thick, tough and large solid materials.
In the booth E2P61, the Automation apartment of Shini will introduce several types of new robots: SS-550 Swing-arm Robot, three Axes Servo Driven Robot of ST3-700-1400T、ST3-1100-1800T and ST3-1800-2400LT-BC. The SS-Series robot is designed for rapid and precise removal of sprue and runner from injection molding machine, and place them into granulator for recycling. Designed with compact structure, elegant appearance, smooth motion and user friendly interface, SS-series win widespread acclaim customers. ST3-1100-1800T Three Axes Servo Driven Robot (Telescopic Arm) is designed for rapid and precise removal of sprue and products from injection molding machine, and place them at desired locations. Designed with compact structure, elegant appearance, smooth motion and user friendly interface, ST3-T Series is best suit for molds with hot runner system. 1800-2400LT-BC series robots are suitable for injection molding machine with clamp forces of below 3600T respectively.
Hot runner department of Shini will bring its self-made different models of nozzles, cylinders, temperature controllers and timing controllers, etc.. In addition, there are products series from Shini-Syncro Extrusion, such as the most popular automatic air ring, thickness gauge, loss-in-weigh gravimetric batch blender and hopper, etc..
News
